圓周分佈鉆孔-宏

[復制鏈接]

ryouss

電梯直達

1^#

發表于 2018-5-20 16:36:44 | 只看該作者 |倒序瀏覽 |閱讀模式

參考

Sub Draw_()
D( d* v9 D5 n$ C. ^8 ?
With UserForm1) X3 R9 A; o' [2 F
'判定資料沒打或是輸入錯誤(起始圓半徑限制不能小於等於鉆孔直徑)8 o3 Z& c1 m# p
If .TextBox4.Value <= .TextBox3.Value Or .TextBox1.Value = "" Or .TextBox2.Value = "" Or .TextBox3.Value = "" Or .TextBox4.Value = "" _ z$ \3 L, t& w0 P2 l
Or .TextBox5.Value = "" Or .TextBox6.Value = "" Then9 T! [3 l2 ~" i" B, Y( z
MsgBox ("Data error Or Data empty")
2 p4 _" N R1 d' |4 i9 i" |" g
Exit Sub8 Y7 C$ n: ~8 R4 }$ @1 q
End If
9 i1 s4 T8 Q$ `
Set swApp = Application.SldWorks, p* s5 t3 K, `# I) C
Set Part = swApp.ActiveDoc& J. G0 T$ q" {) Y* V+ s- R
Set swModel = swApp.ActiveDoc
% D& E. t- u& t4 ^' y
Set swSketchMgr = swModel.SketchManager Y1 I1 f; E9 [2 [* h9 }9 }
9 m2 `6 Z6 X/ e( X2 ?1 u0 [& _6 g
Part.SketchManager.InsertSketch True '依據選取面插入草圖& o$ G! X. G6 i1 ]9 B0 ?' S
'中心圓之座標及作圖
% P" A2 ?) h$ @% i
X1 = .TextBox1.Value / 1000
: V! Y J" [/ B1 M( t" U) \
Y1 = .TextBox2.Value / 1000
; f# b% |; t% K: b
X2 = X1 + .TextBox3.Value / 2 / 1000& `+ t! o. I6 ?! v2 Z' ]# @# l1 K
Set swSketchSegment = swSketchMgr.CreateCircle(X1, Y1, 0#, X2, Y1, 0#)% X( y! W* T# B6 O' @
'圓周分佈之鉆孔* L1 B' Y/ a( K6 \
pi = Atn(1) * 4
, U+ O. F+ L' R
Drill_Diameter = .TextBox3.Value / 1000) R2 K' G w4 m9 H5 B/ x. {
Start_Circle_radius = .TextBox4.Value / 1000, K: ?8 A, m/ _8 n
Circle_number = .TextBox6.Value
2 \. y) d2 A1 }/ s6 v Q* _
ArcAngle = pi '複製孔之圓弧角皆為180度9 _1 L9 Q" J& V7 B
Drill_depth = .TextBox5.Value / 1000 '鉆孔深3 I1 N/ W3 E, a0 m A- K; c' t
For i = 1 To Circle_number
0 i1 W2 P+ H7 m0 Y1 z, z
Circle_radius = i * .TextBox4.Value / 1000 '分佈圓周之半徑
$ E, n' w% \' F6 i* _4 U6 [
Copy_Number = Int(2 * Circle_radius * pi / Start_Circle_radius + 0.5) '分佈圓周之鉆孔數
1 ]$ v! Y4 q. C
'分佈圓之基圓作圖 H1 D% D ?. H! v
BX1 = X1 + Circle_radius
0 U# D& Y# z6 H( h
BX2 = BX1 + Drill_Diameter / 2+ R& H0 W( a( d. U, t
Set swSketchSegment = swSketchMgr.CreateCircle(BX1, Y1, 0#, BX2, Y1, 0#)# r; J6 C4 [( _9 N6 E8 p
'分佈圓之複製孔數,圓周複製參數:圓弧半徑、圓弧角、花紋數、花紋間距(間隔弧度)、圖案旋轉、刪除實例
# R- l9 D; F8 X) f8 i; ~( ]* e
boolstatus = swSketchMgr.CreateCircularSketchStepAndRepeat(Circle_radius, ArcAngle, Copy_Number, 2 * pi, True, "", True, True, True)
7 J( o( F. ~! v4 ?9 j
Next
+ l" o* v) a( I* P
End With
% @- ~" w3 |% `6 I6 C9 E
Dim myFeature As Object) F! X9 p1 N" {& n/ u* T; W
Set myFeature = Part.FeatureManager.FeatureCut3(True, False, False, 0, 0, Drill_depth, 0, False, False, False, False, 1.74532925199433E-02, _; a+ y& Q( C) n( `& ~ U
1.74532925199433E-02, False, False, False, False, False, True, True, True, True, False, 0, 0, False)8 c% J) [' d, }7 p
End Sub/ |1 X( s6 p, e. E. |
* z) W6 l5 b3 h3 s5 e6 n1 f
Sub main()1 x% i# j M: |) I3 Z3 O
UserForm1.Show* t6 [- W: p- c6 h: B ^
End Sub